landisk_sel0.7成功log@開発機

 2011.08頃から使っているuserlandが入っている開発機のlogを今頃取ってみました。
 GNDの接触が悪く文字化けの場合が多いのですが、うまく化けませんでした。
 自分のUSL-5Pでもbootld以外まともに動かない。(笑)

U-Boot 2011.09.landisk_sel0.7 (Apr 13 2013 - 22:46:50)

CPU: SH4
BOARD: IO-DATA Landisk
DRAM:  64MB
Using default environment

PCI: SH7751 PCI host bridge found.
PCI:   Bus Dev VenId DevId Class Int
  00:00.0     - 10ec:8139 - Network controller
  00:01.0     - 1191:0009 - Mass storage controller
  00:02.0     - 1033:0035 - Serial bus controller
  00:02.1     - 1033:0035 - Serial bus controller
  00:02.2     - 1033:00e0 - Serial bus controller
In:    serial
Out:   serial
Err:   serial
Bus 0: OK 
  Device 0: Model: Maxtor 6B250R0 Firm: BAH41BM0 Ser#: B61K5VMH
            Type: Hard Disk
            Capacity: 131071.9 MB = 127.9 GB (268435455 x 512)
Net:   RTL8139#0Warning: failed to set MAC address

Loading file "/boot/u-boot.env" from ide device 0:1 (hda1)
596 bytes read
setenv ipaddr = 192.168.c.d
setenv ncip = 192.168.e.f
setenv bootcmd = landisk_sel 10
setenv bootargs0 = console=ttySC1,115200 mem=64M root=/dev/sda3 rootfstype=ext3
setenv bootargs1 = mem=64M console=ttySC1,115200 usb-storage.delay_use=0 bootld=/etc/init.d/bootld
setenv bootargs2 = console=ttySC1,115200 mem=64M root=/dev/sda3
setenv bootcmd0 = ext2load ide 0:3 0x8c400000 /boot/vmlinuz-3.7.1-landisk;zimageboot 0x8c400000 0x8c001000
setenv bootcmd1 = ext2load ide 0:1 0x8c400000 /boot/bootld.dont_touch/vmlinuz-initramfs-landisk.08;zimageboot 0x8c400000 0x8c0010000
setenv bootcmd2 = ext2load ide 0:3 0x8c400000 /boot/vmlinuz-3.1.4-landisk;zimageboot 0x8c400000 0x8c0010000
Hit any key to stop autoboot:  2  1  0 
landisk boot selector(landisk_sel)...
  If you want to select next bootcmd(n), operate Power SW OFF->ON.
Remainig selectable time is about 10 seconds.
console=ttySC1,115200 mem=64M root=/dev/sda3 rootfstype=ext3
ext2load ide 0:3 0x8c400000 /boot/vmlinuz-3.7.1-landisk;zimageboot 0x8c400000 0x8c001000
Loading file "/boot/vmlinuz-3.7.1-landisk" from ide device 0:3 (hda3)
2129952 bytes read
Setting GDB trap vector to 80000100
Linux version 3.7.1-landisk (root@landiskW1) (gcc version 4.6.3 (Debian 4.6.3-14) ) #1 Mon Dec 31 23:24:30 JST 2012
Boot params:
... MOUNT_ROOT_RDONLY - 00000000
... RAMDISK_FLAGS     - 00000000
... ORIG_ROOT_DEV     - 00000000
... LOADER_TYPE       - 00000000
... INITRD_START      - 00000000
... INITRD_SIZE       - 00000000
Memory limited to 64MB
Booting machvec: LANDISK
Node 0: start_pfn = 0xc000, low = 0x10000
Zone ranges:
  Normal   [mem 0x0c000000-0x0fffffff]
Movable zone start for each node
Early memory node ranges
  node   0: [mem 0x0c000000-0x0fffffff]
I-O DATA DEVICE, INC. "LANDISK Series" support.
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttySC1,115200 mem=64M root=/dev/sda3 rootfstype=ext3
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
PVR=04050005 CVR=20480000 PRR=00000113
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 61440k/65536k available (2414k kernel code, 853k data, 116k init)
virtual kernel memory layout:
    fixmap  : 0xdfff7000 - 0xdffff000   (  32 kB)
    vmalloc : 0xc0000000 - 0xdfff5000   ( 511 MB)
    lowmem  : 0x8c000000 - 0x90000000   (  64 MB) (cached)
            : 0xa0000000 - 0xc0000000   ( 512 MB) (uncached)
      .init : 0x8c333000 - 0x8c350000   ( 116 kB)
      .data : 0x8c25c8dc - 0x8c332080   ( 853 kB)
      .text : 0x8c001000 - 0x8c25c8dc   (2414 kB)
NR_IRQS:8 nr_irqs:8 0
intc: Registered controller 'sh7750' with 20 IRQs
intc: Registered controller 'sh7750_dma8' with 9 IRQs
intc: Registered controller 'sh7750_tmu34' with 2 IRQs
intc: Registered controller 'sh7750_pci' with 8 IRQs
intc: Registered controller 'landisk' with 8 IRQs
Console: colour dummy device 80x25
 sh_tmu.0: used for clock events
 sh_tmu.0: used for periodic clock events
 sh_tmu.1: used as clock source
Calibrating delay loop (skipped)... 266.66 BogoMIPS PRESET (lpj=533333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: SH7751R
devtmpfs: initialized
NET: Registered protocol family 16
PCI: Starting initialization.
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
DMA: Registering sh_dmac handler (8 channels).
DMA: Registering DMA API.
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io  0x1000-0x3fffff]
pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfdffffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:01.0: BAR 6: assigned [mem 0xfd000000-0xfd00ffff pref]
pci 0000:00:02.0: BAR 0: assigned [mem 0xfd010000-0xfd010fff]
pci 0000:00:02.1: BAR 0: assigned [mem 0xfd011000-0xfd011fff]
pci 0000:00:00.0: BAR 0: assigned [io  0x1000-0x10ff]
pci 0000:00:00.0: BAR 1: assigned [mem 0xfd012000-0xfd0120ff]
pci 0000:00:02.2: BAR 0: assigned [mem 0xfd012100-0xfd0121ff]
pci 0000:00:01.0: BAR 4: assigned [io  0x1400-0x140f]
pci 0000:00:01.0: BAR 0: assigned [io  0x1410-0x1417]
pci 0000:00:01.0: BAR 2: assigned [io  0x1418-0x141f]
pci 0000:00:01.0: BAR 1: assigned [io  0x1420-0x1423]
pci 0000:00:01.0: BAR 3: assigned [io  0x1424-0x1427]
Switching to clocksource sh_tmu.1
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
gio: driver initialized
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 120
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
SuperH SCI(F) driver initialized
sh-sci.0: ttySC0 at MMIO 0xffe00000 (irq = 23) is a sci
sh-sci.1: ttySC1 at MMIO 0xffe80000 (irq = 40) is a scif
console [ttySC1] enabled
loop: module loaded
scsi0 : pata_artop
scsi1 : pata_artop
ata1: PATA max UDMA/100 cmd 0x1410 ctl 0x1420 bmdma 0x1400 irq 6
ata2: PATA max UDMA/100 cmd 0x1418 ctl 0x1424 bmdma 0x1408 irq 6
scsi2 : pata_platform
ata3: PATA max PIO0 ioport cmd 0xc0000040 ctl 0xc000002c irq 10
8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:00:00.0 eth0: RTL-8139C+ at 0xfd012000, aa:bb:cc:dd:ee:ff, IRQ 5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 5, io mem 0xfd012100
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 7, io mem 0xfd010000
ata1.00: ATA-7: Maxtor 6B250R0, BAH41BM0, max UDMA/133
ata1.00: 490234752 sectors, multi 0: LBA48 
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 8, io mem 0xfd011000
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6B250R0   BAH4 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
mousedev: PS/2 mouse device common for all mice
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: rtc core: registered rs5c313 as rtc0
landisk_led_init()
hardware is LANDISK
landisk_led_probe()
 registering led 
 registering led 
error - 0
sh_tmu sh_tmu.0: kept as earlytimer
sh_tmu sh_tmu.1: kept as earlytimer
push-switch: version 0.1.1 loaded
TCP: cubic registered
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
rs5c313 rs5c313: setting system clock to 2013-04-16 20:45:45 UTC (1366145145)
EXT4-fs (sda3): mounting ext3 file system using the ext4 subsystem
EXT4-fs (sda3): warning: maximal mount count reached, running e2fsck is recommended
EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
VFS: Mounted root (ext3 filesystem) on device 8:3.
devtmpfs: mounted
Freeing unused kernel memory: 116k freed

INIT: version 2.88 booting

[info] Using makefile-style concurrent boot in runlevel S.
[....] Starting the hotplug events dispatcher: udevdudevd[974]: starting version 175
[ ok .
[....] Synthesizing the initial hotplug events...[ ok done.
[....] Waiting for /dev to be fully populated...[ ok done.
[....] Activating swap...Adding 562268k swap on /dev/sda2.  Priority:-1 extents:1 across:562268k 
[ ok done.
EXT4-fs (sda3): re-mounted. Opts: (null)
[....] Cleaning up temporary files... /tmp /lib/init/rw[ ok .
[....] Loading kernel modules...[ ok done.
[....] Activating lvm and md swap...[ ok done.
[....] Checking file systems...fsck from util-linux 2.20.1
[ ok done.
[....] Mounting local filesystems...[ ok done.
[....] Activating swapfile swap...[ ok done.
[....] Cleaning up temporary files...[ ok .
[....] Setting kernel variables ...[ ok done.
[....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.2.4
Copyright 2004-2012 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/

8139cp 0000:00:00.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
Listening on LPF/eth0/00:a0:b0:67:f4:0c
Sending on   LPF/eth0/00:a0:b0:67:f4:0c
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPOFFER from 192.168.a.b
DHCPACK from 192.168.a.b
bound to 192.168.c.d -- renewal in 3586721 seconds.
[ ok done.
[....] Starting rpcbind daemon...[ ok .
[....] Starting NFS common utilities: statdRPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
 idmapd[ ok .
[....] Cleaning up temporary files...[ ok .

INIT: Entering runlevel: 2

[info] Using makefile-style concurrent boot in runlevel 2.
[....] Starting rpcbind daemon...[....] Already running.[ ok .
[....] Starting NFS common utilities: statd idmapd[ ok .
[....] Exporting directories for NFS kernel daemon...[ ok .
[....] Starting NFS kernel daemon: nfsdrpcbind: connect from 127.0.0.1 to getport/addr(nfs): request from unauthorized host

 mountd[ ok .
[....] Starting enhanced syslogd: rsyslogd[ ok .
Starting btnctrl.
[....] Starting periodic command scheduler: cron[ ok .
[....] Starting disk temperature monitoring daemon: hddtemp:  /dev/sda[ ok .
[....] Starting OpenBSD Secure Shell server: sshd[ ok .
address=fe2440d8
data1=08
address=fe2440d8
data1=03
gio2 write done.
data1=08

Debian GNU/Linux 7.0 landiskW1 ttySC1

landiskW1 login: 

 勝手な思い込みですが、userlandに何かカラクリがあるのでは?と考えいろいろな古いuserlandをUSL-5Pで試してみようかと...